Convergence VTOL BNF Basic, 650mm

  VTOL (Vertical Takeoff and Landing) RC models are usually a mixed bag when it comes to performance. If they are stable, their speed and agility is often lackluster. If they are nimble, pilots have to work harder to transition between hovering and airplane flight. The Convergence® VTOL park flyer changes all that. Its unique design and exclusive flight control software give you the best of both agility and stability while making the transition between multirotor and airplane flight so smooth and predictable, you will feel right at home your first time on the sticks.                                                                                   Sleek and Simple

   Unlike complex VTOL aircraft that rotate the entire wing and require as many as four motors to achieve vertical and forward flight, the Convergence® park flyer uses a simple, yet sleek, delta-wing design with three brushless motors – two rotating motors on the wing and a fixed-position motor in the tail.                                                                                                      In multirotor flight the wing-mounted motors rotate up into the vertical position to provide lift and flight control along with the motor in the tail. In airplane flight, the wing-mounted motors rotate down into the horizontal position and the model’s elevons take over pitch and bank control. Yaw control in airplane flight is provided by differential thrust from the wing-mounted motors.                                                                                                                           

Exclusive Flight Control Software Makes it Easy

  At the heart of it all is flight control software that has been expertly tuned by designer, Mike McConville, so almost any RC pilot can experience the fun of VTOL flight.                                                                                                                                

Automated Transition

 Making the transition between multirotor and airplane flight is as simple as flipping a switch. The flight controller will smoothly rotate the two wing-mounted motors into the correct flight attitude and activate the rear motor as needed.                                                                                                                                        

Stability and Acro Flight Modes

  These two flight modes give you a wide range of performance for every phase of flight.

    • Stability Mode

      • In multirotor flight, Stability Mode will limit pitch and bank angles and work to keep the model level when you release the sticks. This allows you to take off and land like a pro, even if you’ve never flown a multirotor before. In airplane flight, it will limit pitch and bank angles and automatically return the wings to level when the sticks are released.

      • Stability Mode automatically engages during the transition between multirotor and airplane flight. It seamlessly maintains self-leveling and angle limits from one phase of flight to the other, making this the easiest RC VTOL experience you will find anywhere.

    • Acro Mode

      • In Acro Mode there are no angle limits or self-leveling in any phase of flight. During multirotor flight, the model will behave like a conventional multirotor that pitches and banks in whatever direction you want it to fly. It can flip and roll like other multirotors, too.

      • In airplane flight, Acro Mode lets you perform a wide range of aerobatic maneuvers. And because you have the forward thrust of two brushless motors working for you, there is plenty of speed and power to spare. You can even use the differential thrust of the motors to perform unique spinning and tumbling maneuvers.                                                                                                            

        FPV Ready

         The model is designed to accommodate several of the most popular FPV camera systems. There is a camera bay under the nose and a place to mount the video transmitter in the rear of the aircraft. Both locations are easy to access so installation takes just a few minutes.                                                                                 

         

         

        Key Features

        • Multirotor versatility and sport plane agility

        • Designed by champion pilot, Mike McConville

        • Exclusive flight control software makes it incredibly easy to fly

        • Stability and Acro Modes provide a wide performance envelope

        • Powerful brushless motors for outstanding speed and climb performance

        • Super-simple transmitter setup – no complex programming required

        • FPV-ready with camera and video transmitter mounting stations

        • Durable Z-foam™ material                                                                    

          FPV Ready

          The model is designed to accommodate several of the most popular FPV camera systems. There is a camera bay under the nose and a place to mount the video transmitter in the rear of the aircraft. Both locations are easy to access so installation takes just a few minutes.

          Recommended FPV System – All Items Sold Separately

          • Spektrum 650TVL CCD FPV Camera NTSC

          • Spektrum 25mW 5.8GHz Video Transmitter

          • Power Adapter

          • Spektrum 4.3-Inch Video Monitor with Headset

          NOTE: A HAM license is required to operate the Video Transmitter in North America

          Super-Simple Transmitter Setup

          This Bind-N-Fly® version can be flown with any full-range, 6+ channel DSMX®/DSM2® aircraft transmitter and comes equipped with a Spektrum serial receiver that is connected to the flight controller. No complex transmitter setup or programming is required. You use your “GEAR” switch for selecting Stability or Acro mode and your “AUX 1” switch to transition between multirotor and airplane flight.                       

          Approximate Assembly Time:

          No assembly required

          Completion Level:

          Bind-N-Fly Basic

          Flying Weight:

          1.7 lbs (771g)

          Length:

          26.9 in (680mm)

          Material:

          Foam/Carbon

          Minimum Required Radio:

          6+ channel DSMX/DSM2 (not included)

          Motor Size:

          2210-1450Kv Main, 2730 – 1550Kv tail

          Recommended Motor Battery:

          2200-3000mAh 3S 11.1V LiPo (not included)

          Trimscheme Colors:

          Black, Red, Silver

          Wing Area:

          291 sq in (1883 sq cm)

          Wingspan:

          25.6 in (650mm)

           

        Needed to Complete

Gleagle 480N 2.4G 6CH RC Fuel Helicopter RTF DFC 15-Engine 180CC Gasolin Remote Control Nitro Helicopter

  This 480 size Nitro Helicopter is relatively new to the market. This is a ready to fly helicopter out of the box. Each machine is set up and test flown by the factory. So when you get this machine you may notice it has been test flown by the factory once.                                                                                                                       The Global Eagle 480N Helicopter totally designed by Gleagle Technology company and has registered with the appearance patent, utility model patents, invention patent. Its the world\’s smallest fuel helicopter as so far, adopt Taiwan level 15 engine strong power system, choose FBL rotor head structure make it more neat , The frame is constructed from carbon reinforced plastic making it very lightweight while maintaining rigidity and strength,180CC Fuel Tank Drastic 3D maneuvers, big buzzer, smoking, powerful flying scenes take you to the old times.                                                              The good thing with this helicopter is that the helicopter have Fuel & Electric Hybrid function, you can replace the tank/engine/receiver battery as motor /battery/ESC , boom! One new Electric helicopter come out! One machine two choices, what are you waiting for!                                                               The bright spot that the helicopter have Fuel & Electric Hybrid function, you can replace the tank/engine/comitter battery as motor /battery/ESC , boom! One new Electric helicopter come out! One machine two choices, what are you waiting for!                                                                                                                       

  

  

www.goldenstatemint.com/affiliate/broompusher43.html

                                               

1/8Th EP Mad Warrior Racing Edition Truggy Ready to Run RTR Brushless Motor/ESC/Lipo

The new generation of Exceed Rc?s 1/8th scale MadWarrior has finally arrived. The new MadWarrior EP Racing Edition is Exceed?s electric-powered adaptation of the fan favorite MadWarrior. This new variation comes fully equipped with a revamped brushless powertrain and an improved chassis and suspension design. The focus of this new design is entirely on increasing performance and durability to handle the most extreme racing conditions.                                                                                                                                   

  The new MadWarrior EP Racing Edition features a rugged 540L brushless motor rated at 2150kv and a 100-amp XeRun Programmable ESC. The truggy is powered by dual 7.4v 3300mAh LiPo batteries wired in series to generate a peak 14.8v. The MadWarrior EP Racing Edition is equipped with an anodized aluminum chassis, shock towers, top plate and chassis braces which adds to this truggy?s clean look and feel.  The MadWarrior EP is outfitted with CVD front axles and 16mm big-bore aluminum shocks with threaded shock collars. This awesome new platform rides on 5? tires glued to a 17mm hex wheel adding to the sleek design of the chassis. The MadWarrior EP Racing Edition is fully stocked with all these upgrades to handle the pressures of high-level competitive racing.                                                         This new variant of the MadWarrior enjoys a huge increase in performance and reliability and is sure to be a top contender in the Truggy class.                                             

2 Channel 2.4ghz Exceed RC Radio System
540L (36x65mm) 2150kv Sensorless Brushless Motor
XeRun 100A-R Programmable ESC 2-4S LiPo 3A @ 5.75v
ND1009 Metal Geared Steering Servo
Front CVD Axles
4mm thick aluminum front & rear shock towers
3mm thick aluminum chassis plate
Aluminum chassis braces
Aluminum top plate
16mm Big Bore Shocks w/ adjustable threaded collars
Aluminum steering hub
Hardened & Coated Steel Gears 
Multi-piece Anti-Sway Bars
Fully Sealed Ball Bearing Set
Two 7.4v Li-Po 3300mah 20C Cont / 40C Burst batteries included

This item Does NOT come with Charger

Motor

540L Brushless Motor

Bearing

Ball Bearing

Length

20.08 inches (510mm)

Width

16.92 inches (430mm)

Height

8.27 inches (210mm)

Wheelbase

14.88 inches (378mm)

Gear Ratio

1:15.8

Batteries

2 x  Li-po 7.4V 3300mAh Cont. 20C/ Burst 40C Batteries

ESC

100A Brushless ESC

Radio

2.4Ghz Pistol Remote Control

 

Save 50.0% on select products from MissShorthair with promo code 50NENVWE, through 11/1 while supplies last.

Hampton Nautical Ferrari Hydroplane Limited 32″ – RC Speedboat – R

   

Ready To Run Remote Control Ferrari Hydroplane Limited 32″

   This is a high-quality, masterfully crafted Limited Edition racing boat model replica of the fast and powerful Ferrari hydroplanes racing boats.           

32″ Long x 8″ Wide x 11″ High (1:14 Scale)

  • Handcrafted wooden hydroplane model racing boat

  • Waterproof Floating Remote Control racing boat features:

    • 20-25 mph top speed

    • Includes long-distance remote control

    • Rechargeable battery in speedboat with charger

    • Rutter and propeller control

    • 2 Channels, 4 working frequencies                                                                     

Immersion Vortex 275 PRO ARF 350mW, Zipper Packaging (Metall Danny Edition)

Customized for a Legend

Metall Danny’s thrilling forest flying videos inspired a generation of FPV Pilots. The Vortex 275 Metall Danny Special Edition was customized for Danny, to meet the needs of forest flying. With the classical robustness of the Vortex 250 Pro, longer arms to swing 6″ props, custom 2205 V-Spec motors, and a CCD Camera. In a world where quads are getting smaller, and their ability to carry a GoPro disappears, the Vortex 275 likes to be a little different.                                                                                                                                                                                            

Tuned by a Pro

As with all Vortex quads, pro-tunes are included to eliminate the complex tuning process. Danny has tweaked the PIDs to perfection, and we have included them in the default firmware for the quad.                                                    

Out with Steel, in with Titanium!

The stock Vortex 250 Pro shipped with a steel screw-set. Extremely strong, un-necessary weight when whipping around a dense forest.

The Metall Danny edition replaces this with a Titanium screw set, significantly lighter, and much stronger than aluminium equivalents.                                   

V-Spec 2205-2100kV Power

Custom V-Spec 2205-2100kV motors swing 6″ props with anger! These motors were custom-designed for this quad.

Beautifully milled and anodized, using single-strand wiring.

Robust enough to survive the occasional ‘kiss’ from a passing pine-tree.                                        

Physical meets Virtual

 The Metall Danny Vortex 275 is available in the popular Liftoff simulator.

The larger props, motors, etc. are all simulated using the advanced physical models driving the simulator.

Fly before you Buy!                                                                                                                      

 

PRODUCT SPECIFICATIONS

Initial Release Date: August 2016

Weight: ~435g without battery, or HD camera

Power Requirements: 3s-4s LiPo (typical)

ESCs: Full Custom, 20A cont. 22A peak, rotorSENSE, OneShot125

Motors: Custom V-Spec 2205-2000kV, with 3mm axles, 5mm shafts

Props: OEM HQ 6035

Flight Camera: FatShark 600 TVL CCD (or equivalent)

HD Camera: GoPro Hero, Hero 3/4/5

Receiver Compatibility: CPPM, S-Bus, Spektrum™, XBus, SumH, SumD (no external adapters required) (Auto-Sense!)

Flight Time: Highly dependent upon battery, and flying style

Note: Compatible receiver and display device required for initial setup and use, not included.

  

Freewing Mirage 2000C-5 80mm EDF Jet PNP RC Airplane

  The Dassault Mirage 2000 is a French multirole, single-engine fourth-generation jet fighter manufactured by Dassault Aviation. It was designed in the late 1970s as a lightweight fighter based on the Mirage III for the French Air Force (Arme de l.Air). The Mirage 2000 evolved into a multirole aircraft with several variants developed, with sales to a number of nations. The variants include the Mirage 2000N and 2000D strike variants, the improved Mirage 2000-5 and several export variants. Over 600 aircraft were built and it has been in service with nine nations.                                                                                                                                                    We are proud to offer the Mirage 2000 as our latest model in the 12 blade 80mm EDF offering. As you’ve come to expect from Freewing Model, the Mirage 2000 is loaded with scale features and performance componentry. The new 80mm 12-blade EDF with metal housing powered by a powerful 1750kV motor produces nearly 6 pounds of thrust for awesome speed and incredible maneuverability. The sound produced from the 12 blade EDF will simply blow you away. While 5 and 6 blade EDF produce a high pitched whining sound, the 12 blade EDF with metal housing produces the “whoosh” and air crushing sound similar to a gas turbine jet.                                                        Additional upgraded features include a 80A Hobbywing ESC, 9g precision servos, and electronic retracts with full metal shock absorbing struts. Own the latest, highly detailed, best built RC foam jet on the market from Freewing – the Mirage 2000.                                                                                                     

 

 

FEATURES:

12 Blade factory balanced EDF with metal housing combined with 3530-1750KV brushless outrunner motor produces realistic jet turbine sound and an incredible 6 lbs of thrust

Composite fan blades combined with metal EDF housing make the Mirage 2000 AMA compliant (the fan blades themselves are NOT metal, so there are no flying restrictions)

Super scale details include hand painted, scale-sized pilots, full instrument panel, refueling probe, scale drop tanks, airfoil panel lines, and complete French Air Force graphics package

80 Amp Hobbywing ESC with 5A BEC

Electronic retractable landing gear with all metal shock-absorbing struts

Steerable, shock absorbing nose gear for enhanced ground maneuverability

Spring operated nose gear door

Carbon spars and EPO foam construction provide the perfect balance between strength and flexibility

Nylon hinges on all control surfaces (superior to foam hinges)

Outrunner motor, servos, ESC and EDF come pre-installed for your convenience

Removable magnetic nose cone, and removable wings and vertical stabilizer for convenient transport                                                                                                            

INCLUDES:

Freewing 80mm 12-Blade Metal EDF Mirage 2000C-5 – PNP Rc airplane             

REQUIRES:

6 Channel Radio – Select a minimum 6 channel radio

6 Channel Receiver – Select a minimum 6 channel receiver

6 Cell 22.2V 4000 mAh LiPo Battery with EC5 connector

6 Cell Compatible Battery Charger – Select a minimum 6 cell (6S) charger

PRODUCT SPECIFICATIONS:

Wingspan

790mm / 31.10in

Length

1250mm / 49.21in

Flying Weight

2200g / 78oz

CG (Center of Gravity)

check manual

Power System

3530-1750kV Brushless Outrunner Motor

Electronic Speed Control

80A ESC, 5A BEC, EC5 Connector

Propeller / EDF

80mm Metal EDF with 12 Blade Fan

Servos

9g metal gear reverse with 300mm lead : nose gear steering
9g metal gear standard with 550mm lead : left aileron, right aileron
9g metal gear standard with 300mm lead : rudder

Landing Gear

Electronic retractable main gear and steerable nose gear with all metal shock absorbing struts

Required Battery

6S 22.2V 4000mAh 60C LiPo

Required Radio

6 Channel

Ailerons

Yes

Elevator

Yes

Rudder

Yes

Flaps

No

Lights

No

Hinge Type

Nylon hinges

Material

EPO Foam

Skill Level

Intermediate / Advanced

Build Time

2 Hours

Recommended Environment

Outdoor

  

  

GARTT 700 DFC TT RC Helicopter Torque Tube Version Super Combo

The amazing GARTT 700 DFC Helicopter is on the market now! After hundreds of test 

flights by the world-class pilots, the GARTT 700 Helicopter can fit each type of flight, 

Hard 3D Maneuvers or Speed Flight, just use your imaginations!                                                                                                

  The brand new 700 DFC (direct flight control) rotor head utilizes 

high quality radial bearings, thrust bearings and is anodized in 

a beautiful silver finish. Having low center of gravity, low resistance, 

responsive controls, these feathers led you to have incredible experiences 

during flight.                                                                                                                                    Also with the stunning hand-paint unique Fire canopy, low wind

resistance streamline design, no extra movements, the GARTT 700

Helicopter will sure give you more surprises!

GT700, made for flight.                                                                                                             

 Brand Name: GARTT Type: Helicopter Features: Remote Control Aerial Photography: No Control Channels: 6 Channels Action Time: 20min Material: Plastic,Carbon Fiber,Metal Model Number: 700DFCTT-C State of Assembly: Almost Ready Dimensions: 1345*360mm Charging Voltage: 3.3v Charging Time: 1hour Warning: over 18 Warranty: 3 months Remote Control: No Age Range: Grownups Motor: Brushless Motor Controller Mode: MODE1,MODE2 Plugs Type: no Controller Battery: transmitter battery Remote Distance: 500-800m Power Source: Electric Package Includes: 700 helicopter kit Features: Cruise.                                                                       

  

Kyosho Mad Crusher GP 4WD Nitro Powered RC Truck

New monster machine dominates the roughest roads in style with scale truck body and 5-link suspension.

  Let the might and power of this monster machine inspire you with its dominant presence and performance over the toughest terrain. Get your adrenalin pumping by ripping around wide-open spaces at full throttle as you wreak true R/C truck mayhem! Based on the heavy-duty Mad Force Cruiser chassis, the new MAD CRUSHER incorporates a newly developed 5-link suspension system featuring ball joint upper and lower links in combination with lateral rods that deliver a deeper, supple stroke, more characteristic of rock crawlers. Equipped with the powerful KE25 engine, you can ride over any surface from tarmac to off-road in ‘70s American pick-up truck style with realistic scale wheels and tires. Simply add fuel and batteries to the MAD CRUSHER Readyset and you can get straight into monster trucking action!                                                                                                                

  • Fully assembled Readyset only requires fuel and batteries.

  • 1/8 scale Mad Force monster truck chassis base incorporates new 5-link suspension.

  • Pre-cut and painted scale body complete with decals applied recreates the 70’s American truck style.

  • Rigid axles on front and rear with solid casing effectively transfer power into traction.

  • Diff gears incorporate steel spiral gears on front and rear to handle high power loads.

  • Large capacity 150cc fuel tank enables long run times.

  • Includes Syncro KT-231P+ transmitter and Syncro KR-331 receiver with failsafe function.

  • Receiver and battery are stored in radio box for protection against shock and dirt.

  • Waterproof high-torque KS5031-09MW steering servo incorporates metal gears for reliable control of the big chassis                                                                                                                          Supple deep stroke characteristics of the new 5-link suspension supports the dynamic performance of this 4,000g + heavyweight machine.                                                                                                                                                                                                          Lateral rods equipped on front and rear control the movement of the suspension to ensure superior surface tracing and stability.                                                                                                    Chrome plated Injection molded grill, bumper, wipers and mirrors are included to create a breathtaking level of detail. Optional Light Unit (No.SCW018) can also be installed.                                                                                                                                                     Massive 150mm x 70mm block-pattern tires and black wheels deliver sure-footed performance in formidable style.                                                                                                                                Engine break-in is made easy even for beginners with the inclusion of two reducers; silver for break-in and blue for normal running.                                                                                              The 3-speed automatic transmission makes effective use of the KE25 engine’s power band. Enables powerful acceleration up the power band and higher maximum speed.                                                                                          

                                                                              < Readyset Contents >

The Jersey City Tug Boat Kit w/9″ Beam (1/32 Scale) 36″

  The Jersey City is a popular addition to the Dumas tugboat collection. A railroad tug from the 1960s, the Jersey City can still be seen working on the eastern seaboard.                                                             She is designed for radio control using a two channel radio, or this detailed workhorse makes a great static model for your den or office.                                                                 

JERSEY CITY

  Built in 1960, by the Dravo Corporation of Pittsburgh, Pennsylvania (hull #3946) as the Jersey City for the Pennsylvania Railroad Company of Philadelphia, Pennsylvania. 
  In 1968, the Pennsylvania Railroad Company merged with New York Central Railroad Company of New York, New York. To form the Pennsylvania Central Transportation Company of New York, New York. Where the tug retained her name.                                                                                                                                                            In 1974, the tug was acquired by the Crescent Towing and Salvage Company Incorporated of New Orleans, Louisiana. Where the tug was renamed as the Glenn Smith.                                                                                                                          In 2008, the Crescent Towing and Salvage Company, renamed the tug as the Admiral Jackson.                                                                                                                  In 2008, the tug was rebuilt and repowered. The project included a complete redesign of the vessel. Including the wheelhouse, with improved window placement, and low profile stacks for maximum visibility.                                                                                                                 Her stern section, and propulsion system, were removed, and replaced. Her existing single, EMD 12-567C diesel engine was removed. And, replaced with two, eight cylinder, General Electric 228, diesel engines. With Reintjes reduction gears, at a ratio of 4:1. Turning two, 85(in) Bollinger stainless steel, fixed pitch propellers. Mounted in 86(in) type 37 kort nozzles. With stainless steel inner rings. And, a maximum range of forty five degrees for increased maneuverability. She is a twin screw tug rated at 4,200 horsepower.
(Paul Strubeck)                                                                                                                                                        

The Jersey City
Length: 36 inches 
Beam: 9 inches
Scale: 1/32

*Additional parts required for R/C:

Running Hardware:  #2367 for single screw operation                                 Power: #2004 Electric Motor 
Speed Control: #8314 Electronic Speed Control 
Battery: #8302 7.2v NiCad Flatpack 
Charger: #8315 NiCad Battery Charger 
Radio Control: #8812-1 2 Channel Radio Control w/ servo                                        Credits: http://www.tugboatinformation.com/                                                                                                                                                                                                                                                                                                              

  

ARRIS C250 V2 FPV Racing Drone RTF with Radiolink AT9S Radio

  ARRIS C250 V2 RTF with Radiolink AT9S is fully assembled, tuned and tested before leaving the factory, it is ready to fly. ARRIS C250 V2 is one more professional 250 fpv racing drone it has the advantage of simple structure and high strength.ARRIS C250 V2 adopts 4in1 30A tower for the first time instead of separate ESC, flight controller and OSD. This not only decrease the weight of the drone, protect the ESC better, but also making the future maintainance more convenient.                                                                                       ARRIS C250 V2 is made of pure carbon fiber material. With water transfer painting technology,it look so charming. The upper plate and side plate adopts 1.5mm pure carbon fiber material, decrease the weight of the whole frame. Meanwhile, the motor arm adopts 4mm carbon fiber material, ensure the strength of the frame. The total weight of the frame is about 137g.With the simplify one-piece design and lower gravity center design, all kinds of flight actions can be done with facility.The layout design of the C250 V2 is reasonable, the standard flight controller and PDB board can install there.On the frame, there is reserved space for the XT60 female battery connector.The motor arm has holes for 220x series motors, and both 5 inches and 6 inches propellers can install on the C250 V2 frame.                                     

The main advantages of the 4in1 30A Tower:

1. With the double layer design, you just need to plug the pins between esc and flight controller, flight controller and other electronic components. The layout is more concise, decrease the weight of the drone, provided guarantee for flight performance improvements.
The power for flight controller and camera is provided by the BEC on the flight controller. The power for video transmitter is provided by battery. This improves the anti-interference of the video transmission.

2. The tower integrated the OSD, avoid to install it additionally and the adjustment.The drone could get a quick response to the throttle during the flight.

3. The Tower structure design protects the ESC well during the flight. According to our experience, some of the ESC were damaged by the propeller rotation or tree brunch cut, and some of the ESC were damaged due to the broken of the motor arm during the crash when it installed on top of the motor arm. Sometimes, in order to protect the ESC, we added ESC cover to protect it. From this, the weight of the drone increased. For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESCs can be protected quite well and make it looks better.             

With the high performance ARRIS X2205 2300KV brushless motor, the ARRIS C250 V2 has outstanding power.
Main Features:

1. Adopts the brand new M5 steel shaft, improving the structure strength.
2. Anti-slip pro design.
3. Upgrade to centrifugal fan design, optimizing the heat dissipation.
4. Adopts original Japan NSK bearing, improving the performance of the motor.
5. Adopts N52 tile-shaped magnets.
6. The motor passed more than 20 kinds of tests before leaving the factory, ensure the quality of the motor.                                                                                                   The ARRIS C250 V2 adopts with the latest5042 propeller, it has bigger windward area, well balance and strengthen root, and the efficiency is 10% higher than normal propeller. This propeller is the first choice of FPV racing drones.                                                                                                                                                     ARRIS XAT700M FPV Mini Camera for FPV Racing Drones–ARRIS XAT700M HS1177 fpv mini camera is specially designed for FPV. This camera performs well in both bright and dark condition with 700TVL high quality image. And the camera angle on the drone is adjustable.                                   

  ARRIS 5.8g 200mW 40-CH video TX and antenna pre-assembled.The ARRIS TS5823L with LED is transmitting a full range of 40 channels and only weighs 10g. It’s perfect for a wide range of aircraft!With a goggle or monitor in hand, you can begin your FPV journey.                                                               ARRIS X-Speed C250 V2 has integrated with a remote controller battery warning buzzer, pilot can set the threshold (adjustable) according to CF parameter-adjustment software. In addition, you can also locate your racing drone through triggering the buzzer with the switch D on the transmitter.               Self-level mode is the easiest to fly, because when you leave the stick at the center and not controlling it, your drone just level itself and stays there.This mode is good for beginners.
Manual mode is useful for acrobatics such as flips or rolls, or FPV when smooth and fast control is desired. The picture below is what we set on our own Radiolink AT9 Radio.                                                                                                               RadioLink AT9 9-Channel 9CH 2.4GHz Transmitter + R9D Receiver.The AT9 radio is with high performance-price ratio. And it can support strength, receiver voltage monitored, extending battery voltage, temperature, motor RPM, GPS etc.                                                                                                                                                                                            

High safety ARRIS 4S 1500mah Lipo Battery

  ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer. The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products.For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test,1.2M Drop test,MDS report for it, for the test report, you can check here.                                                                                                                                     

 

 

Main Features:

1. Simple structure frame installed with tower structure ESC/PDB, easy to assemble and easy to repair.
2. High quality 3K Carbon fiber frame, the material is imported from Janpan
3. 4mm thick arms, super strong and durable
4. Super Light frame, only $136g
5. The tower ESC/FC comes with integrated OSD, no need to install it separately
6. The angle of the FPV camera is adjustable
7. 4mm thick arms, super strong and durable
8. High efficiency X2205 2300KV motor provides you better performance and longer working life
9. High quality 5042 3 blade propeller, 10% higher efficiency than normal propellers
10. High safety 4S 1500mah 50C lipo battery                                                                                                                                                                                                                              

Specifications:

Dimension:195mm x 230mm x 42mm (Propellers not included)
Diagonal Wheelbase: 250mm
Flight Controller: F3 flight Controller
Frame Material: Pure Carbon fiber
BNF weight:350g
Radio System: Radiolink AT9 with R6DSM receiver
Camera: ARRIS XAT700M FPV Mini Camera
FPV TX: 5.8G 200mw 40CH
Antenna: 5.8G Antenna
Flying Time: 10min hovering
Battery: ARRIS 4S 1500mah 50C Lipo                                                                                                                                                                                                                                                              

  

Powered by AWS